The following manual will get you know all the brushed flight controllers from BETAFPV Hobby quickly. There are 4 version of brushed FC boards in stock nowadays and several versions are discontinued. Please distinguish the board in your hands.
The 4 kind of brushed FC boards including:
- F3 EVO + Frsky Rx (V1.1)
- F3 + Frsky Rx + OSD (V2)
- F3 + DSMX Rx + OSD
- F3 + OSD
- F4 + SPI Frsky RX + OSD
- F4 + Internal DSMX RX+ OSD
F4 + Internal DSMX RX+ OSD
- CPU: STM32F411CEU6
- Six-Axis: MPU6000
- ESC: All FETs are rated at 30A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors.
- Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
- Firmware version: Betaflight MATEKF411RX 3.5.0
- Receiver: DSM2/DSMX
- Weight: 3.8g
F4 + SPI Frsky Rx + OSD
- CPU: STM32F411CEU6
- Six-Axis: MPU6000
- ESC: All FETs are rated at 30A maximum
- Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
- Firmware version: Betaflight MATEKF411RX 3.4.0
- Receiver: SPI Frsky potocol (D8 or D16)
- Weight: 3.8g
F3 EVO + Frsky Rx (V1.1)
- CPU: STM32F303CCT6
- Six-Axis: MPU6500
- ESC: All FETs are rated at 6.3A maximum
- Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
- Firmware version: Betaflight SPRACINGF3EVO
- Receiver: Frsky D8 potocol with PA (SBUS)
- Weight: 3.0g
F3 + Frsky Rx + OSD (V2)
- CPU: STM32F303CCT6
- Six-Axis: MPU6000
- ESC: All FETs are rated at 30A maximum
- Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
- Firmware version: Betaflight BETAFLIGHTF3
- OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
- Receiver: Frsky D8 potocol (SBUS)
- Weight: 3.8g
F3 + DSMX Rx + OSD
- CPU: STM32F303CCT6
- Six-Axis: MPU6000
- ESC: All FETs are rated at 6.3A maximum
- Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
- Firmware version: Betaflight BETAFLIGHTF3
- OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
- Receiver: DSMX potocol (SBUS)
- Weight: 3.4g
F3 + OSD
- CPU: STM32F303CCT6
- Six-Axis: MPU6000
- Size: 26mm x 26mm, fully compatible with the Inductrix quad frame and mounting pattern
- Firmware version: Betaflight BETAFLIGHTF3
- Receiver interface: 5V, 3.3V, UART2 and PPM
- OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
- Weight: 3.0g
The FC boards below are discontinued and does not produce and sell.
- F3 + Frsky Rx + OSD (V1.1)
F3 + Frsky Rx + OSD (V1.1)
- CPU: STM32F303CCT6
- Six-Axis: MPU6000
- ESC: All FETs are rated at 6.3A maximum
- Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
- Firmware version: Betaflight BETAFLIGHTF3
- OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
- Receiver: Frsky D8 potocol (SBUS)
- Weight: 3.4g
F3 EVO + Frsky Rx (V1.0)
- CPU: STM32F303CCT6
- Six-Axis: MPU6500
- ESC: All FETs are rated at 6.3A maximum
- Firmware version: Betaflight SPRACINGF3EVO
- Receiver: Frsky D8 potocol with PA (SBUS)
- Weight: 3.0g
F3 + Frsky Rx + OSD (V1.0)
- CPU: STM32F303CCT6
- Six-Axis: MPU6000
- ESC: All FETs are rated at 6.3A maximum
- Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
- Firmware version: Betaflight BETAFLIGHTF3
- OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
- Receiver: Frsky D8 potocol (PPM)
- Weight: 3.4g
F3 EVO
- CPU: STM32F303CCT6
- Six-Axis: MPU6500
- ESC: All FETs are rated at 6.3A maximum
- Firmware version: Betaflight SPRACINGF3EVO
- Weight: 3.0g